/etc/sysconfig/network-scripts/init.ipv6-global

/etc/sysconfig/network-scripts/init.ipv6-global
1 내용 예시[ | ]

#!/bin/sh
#
# init.ipv6-global
#
#
# Taken from: init.ipv6-global
# (P) & (C) 2001-2005 by Peter Bieringer <pb@bieringer.de>
#
#  You will find more information on the initscripts-ipv6 homepage at
#   http://www.deepspace6.net/projects/initscripts-ipv6.html
#
# RHL integration assistance by Pekka Savola <pekkas@netcore.fi>
#
# Version: 2005-01-04
#
# Calling parameters:
#  $1: action (currently supported: start|stop|showsysctl)
#  $2: position for start|stop (currently supported: pre|post)
#
# Called by hooks from /etc/[rc.d/]init.d/network
#
# Uses following information from /etc/sysconfig/network:
#  IPV6FORWARDING=yes|no: controls global IPv6 forwarding (default: no)
#  IPV6_AUTOCONF=yes|no: controls global automatic IPv6 configuration
#   (default: yes if IPV6FORWARDING=no, no if IPV6FORWARDING=yes)
#  IPV6_AUTOTUNNEL=yes|no: controls automatic IPv6 tunneling (default: no)
#  IPV6_DEFAULTGW=<ipv6address[%interface]> [optional]
#  IPV6_DEFAULTDEV=<interface> [optional]
#



. /etc/sysconfig/network

cd /etc/sysconfig/network-scripts
. ./network-functions

# Get action and hook position
ACTION="$1"
POSITION="$2"

[ -f /etc/sysconfig/network-scripts/network-functions-ipv6 ] || exit 1
. /etc/sysconfig/network-scripts/network-functions-ipv6

# Initialize IPv6, depending on caller option
case $ACTION in
    start)
	case $POSITION in
	    pre)
		# IPv6 test, module loaded, exit if system is not IPv6-ready
		ipv6_test || exit 1


		if [ "$IPV6FORWARDING" = "yes" ]; then
			ipv6_global_forwarding=1
			ipv6_global_auto=0
		else
			ipv6_global_forwarding=0
			if [ "$IPV6_AUTOCONF" = "no" ]; then
				ipv6_global_auto=0
			else
				ipv6_global_auto=1
			fi
		fi

		# Reset IPv6 sysctl switches for "all", "default" and still existing devices
		for i in /proc/sys/net/ipv6/conf/* ; do
			interface=${i##*/}
			sinterface=${interface/.//}
			# Host/Router behaviour for the interface
			/sbin/sysctl -e -w net.ipv6.conf.$sinterface.forwarding=$ipv6_global_forwarding >/dev/null 2>&1

			# Autoconfiguration and redirect handling for Hosts
			/sbin/sysctl -e -w net.ipv6.conf.$sinterface.accept_ra=$ipv6_global_auto >/dev/null 2>&1
			/sbin/sysctl -e -w net.ipv6.conf.$sinterface.accept_redirects=$ipv6_global_auto >/dev/null 2>&1
		done
		;;

	    post)
		# IPv6 test, module loaded, exit if system is not IPv6-ready
		ipv6_test || exit 1


		if [ "$IPV6_AUTOTUNNEL" = "yes" ]; then
			ipv6_enable_autotunnel
			# autotunnel interface doesn't require a MTU setup
		fi

		## Add some routes which should never appear on the wire
		# Unreachable IPv4-only addresses, normally blocked by source address selection
		/sbin/ip route add unreach  ::ffff:0.0.0.0/96
		# Unreachable IPv4-mapped addresses
		/sbin/ip route add unreach  ::0.0.0.0/96
		# Unreachable 6to4: IPv4 multicast, reserved, limited broadcast
		/sbin/ip route add unreach  2002:e000::/19
		# Unreachable 6to4: IPv4 loopback
		/sbin/ip route add unreach  2002:7f00::/24
		# Unreachable 6to4: IPv4 private (RFC 1918)
		/sbin/ip route add unreach  2002:0a00::/24
		/sbin/ip route add unreach  2002:ac10::/28
		/sbin/ip route add unreach  2002:c0a8::/32
		# Unreachable 6to4: IPv4 private (APIPA / DHCP link-local)
		/sbin/ip route add unreach  2002:a9fe::/32
		# Unreachable IPv6: 6bone test addresses
		/sbin/ip route add unreach  3ffe:ffff::/32

		# Set default route for autotunnel, if specified
		if [ "$IPV6_DEFAULTDEV" = "sit0" -a "$IPV6_AUTOTUNNEL" = "yes" ]; then
			if [ -n "$IPV6_DEFAULTGW" ]; then
				ipv6_set_default_route $IPV6_DEFAULTGW $IPV6_DEFAULTDEV sit0
			elif [ -n "$IPV6_DEFAULTDEV" ]; then
				ipv6_set_default_route "" $IPV6_DEFAULTDEV sit0
			fi
		fi
		;;

	    *)
		echo "Usage: $0 $1 {pre|post}"
		;;

	esac
	;;

    stop)
	case $POSITION in
	    pre)
		;;

	    post)
		# IPv6 test, no module loaded, exit if system is not IPv6-ready
		ipv6_test testonly || exit 0


		for i in /proc/sys/net/ipv6/conf/* ; do
			interface=${i##*/}
			sinterface=${interface/.//}
			# Assume Host behaviour
			/sbin/sysctl -e -w net.ipv6.conf.$sinterface.forwarding=0 >/dev/null 2>&1

			# Disable autoconfiguration and redirects
			/sbin/sysctl -e -w net.ipv6.conf.$sinterface.accept_ra=0 >/dev/null 2>&1
			/sbin/sysctl -e -w net.ipv6.conf.$sinterface.accept_redirects=0 >/dev/null 2>&1
		done

		# Cleanup still existing tunnel devices
		ipv6_cleanup_tunnel_devices

		# Shut down generic tunnel interface now
		if ipv6_test_device_status sit0 ; then
			/sbin/ip link set sit0 down
		fi
		;;

	    *)
		echo "Usage: $0 $1 {pre|post}"
		;;

	esac
	;;

    *)
	echo $"Usage: $0 {start|stop|reload|restart|showsysctl}"
	exit 1
	;;
esac
2 같이 보기[ | ]
